![Step-By-Step: Gelcoat Restoration Process for Beginners](http://boatloverstowel.com/cdn/shop/articles/iStock-1215641608_{height}x{width}.jpg?v=1721308321)
Step-By-Step: Gelcoat Restoration Process for Beginners
Table of Contents:
- Introduction to Gelcoat Restoration
- Step 1: Tools and Materials Needed for the Restoration Process
- Step 2: Preparing the Surface for Gelcoat Restoration
- Step 3: Applying the Gelcoat Restoration Product
- Step 4: Buffing and Polishing the Gelcoat to a High Shine
- Step 5. Final Steps and Maintenance Tips for Keeping Your Gelcoat Looking New
- Shop Boat Lover’s Towel
Introduction to Gelcoat Restoration
UV exposure can cause the surface of the shiniest boats to eventually fade due to the oxidation of the gelcoat. That once-lustrous look will gradually fade away due to the oxidation of the gelcoat. However, everything's not lost as long as you know how to repair a boat's gelcoat. Lucky for you, this blog will explain how you can get that showroom shine back on your boat by restoring the gelcoat.
Step 1: Tools and Materials Needed for the Restoration Process
Using gelcoats on your boat requires more effort than cleaning or restoring car coatings due to their thick nature. Specialized tools are needed for high-quality detailing, as automotive products typically lack the polishing power needed for marine-grade treatments. To prevent damage to your boat's gelcoat, equipment should be specifically designed for boat detailing.
You’ll need a whole lot of items to do the job right, including:
- Medium or coarse deck brush
- Microfiber wash mitt
- Boat erasers
- Silicone squeegee
- All-purpose cleaner/degreaser
- Applicators pads
- Compound polish
- Wash buckets
- Rotary buffer and polisher
- Goggles
- Soft handheld brush
- Telescoping extension pole
- Knee pads
- Boat soap
- Stain remover
- Polishing and buffing pads
- Microfiber rags
- Wax sealant
- Boat chamois
- Hose and nozzle
Step 2: Preparing the Surface for Gelcoat Restoration
To restore the look of your boat, first wash and remove any surface filth and debris with cleaning tools and quality microfiber rags. Yellow and rust stains can be removed using elbow grease or a certified rust remover. Use splash-proof goggles and gloves for a safer application.
Wet/dry sanding may be required in severe circumstances where the gelcoat cannot be revived by compounding due to high oxidation levels. Once you’ve fully cleaned/sanded the surface, you’re ready to apply the restoration product.
Step 3: Applying the Gelcoat Restoration Product
Next, use a high-quality polishing compound containing powerful abrasives, such as a rubbing compound specially formulated for fiberglass. Apply the product, then rub the surface until it is smooth. Stop rubbing once the finish looks shiny. Continue polishing the rest of the boat until the gelcoat reaches a glossy look. If there was significant enough oxidation, the "factory" finish may not be fully restored.
Step 4: Buffing and Polishing the Gelcoat to a High Shine
When you start gelcoat polishing, apply wax to the surface using a rotary buffer and pad. Make sure it covers a significant portion of the boat. You should avoid overapplying, and remove the excess wax with a buffing pad. Allow the wax to haze, then remove it with a polisher.
Step 5. Final Steps and Maintenance Tips for Keeping Your Gelcoat Looking New
The last step is maintaining the gelcoat after it has been restored. By performing regular washing and maintenance with the guidance of the following tips, you can help keep the gelcoat of your boat looking new.
- Regularly wash and dry your boat to prevent staining, salt buildup, and mold. This will improve the look and lifespan of your boat’s surface.
- How often you wash it depends on the weather. Hotter climates and excessive sunshine require frequent polishing due to gelcoat degradation.
- Keeping the hull sealed is another way to help minimize oxidation.
- Store your boat in a garage or storage unit, as cooler climates improve longevity and reduce waxing frequency.
- For hotter climates, we recommend keeping your boat in a garage or covered when not in use.
- Use specific soaps for cleaning, especially oxidation-removal marine soap. The gelcoat should be polished every three to six months.
- Use reputable marine-grade products, such as protection wax with durable adhesives and UV fillers, for polishing and protecting gelcoat and paint. Apply these products when detecting a possible oxidation buildup.
Boat Lover’s Towel has superior boat cleaning and detailing supplies, including The Glosser® wash and wax wipes.
Shop Boat Lover’s Towel
![How to Buff a Boat: A Step by Step Process](http://boatloverstowel.com/cdn/shop/articles/Screenshot_2024-06-25_115408_{height}x{width}.png?v=1719297294)
How to Buff a Boat: A Step by Step Process
Table of Contents:
- Introduction to Boat Buffing
- Gather the Necessary Supplies and Equipment
- Wash and Dry the Boat Thoroughly
- Inspect the Boat for Any Imperfections
- Use a Compound to Buff Out Scratches and Oxidation
- Polish the Boat to Restore Shine and Protect the Surface
- Apply a Wax or Sealant for Added Protection
- Final Inspection and Finishing Touches
- Tips for Maintaining a Buffed Boat
- Conclusion
Introduction to Boat Buffing
Just like vehicles on the road, boats are exposed to wear and tear when they are hauled to the dock or out on the water. Responsible boat owners often end up wanting to wax the hull of their boat. This helps protect the outer layer of paint and offers another layer of protection while restoring its shine.
Rotating buffers are often used by professionals for waxing boats, but they can be dangerous if not used correctly. An orbital buffer is safer as it vibrates only back and forth, but only for applying a thin layer of wax. Here are the steps that boat lovers should take when they want to learn how to buff and wax a boat on their own.
-
Gather the Necessary Supplies and Equipment
For DIY enthusiasts, a dual-action boat polisher is ideal. Since it oscillates and spins, it is a safer option than a rotating or orbital buffer. It is lighter, less prone to damage, and faster than hand-working. Typically, these buffers offer different speed settings, which is important because different tasks require different speeds.
Materials you will need also include:
- Sponge
- Bucket with dish detergent
- Hull and bottom boat cleaner
- Compound
- Hull wax or a wax and compound combo
- Microfiber towel
-
Wash and Dry the Boat Thoroughly
To clean a boat, use warm water, soap, and a sponge to remove dirt and debris. Use ordinary dishwashing detergent instead of specialty soaps for the removal of as many contaminants as possible. This is less expensive and eliminates more oils and old wax than milder soaps. Rinse the boat thoroughly and let it air dry.
-
Inspect the Boat for Any Imperfections
Take a pass around the boat and see if any spots still appear dirty, and rewash until you achieve the desired look.
-
Use a Compound to Buff Out Scratches and Oxidation
The first thing to know about how to buff a boat gelcoat is that you should use a rubbing compound before polishing if your boat has a scratched or oxidized gelcoat. Rubbing compound is more abrasive than polish and is used when the oxidation level is too high for polishes to handle. Work the compound in a circular motion until the gelcoat becomes smooth. Then wipe away any remaining rubbing compound with a microfiber towel.
-
Polish the Boat to Restore Shine and Protect the Surface
Polish is a finer abrasive than rubbing compound, and it is used to leave it mirror-smooth and ready for waxing. Apply a dime-size dollop of the chosen product to the buffer pad. Firmly place it against the hull and work it in an overlapping 3-by-3-foot section of the boat. Turn off the buffer and repeat the process. Then check that the surface feels smooth as glass, and then wipe away excess polish with a microfiber towel.
-
Apply a Wax or Sealant for Added Protection
Wax the boat with boat wax to prevent oxidation and fill in blemishes, resulting in a glossy, smooth finish and added surface protection after drying and buffing.
-
Final Inspection and Finishing Touches
Take a look around the boat and make sure the final results are up to your standards. You can add a little more wax to any areas that might need some more work before it’s showroom-ready.
Tips for Maintaining a Buffed Boat
-
Use the right products.
-
Wash the boat before you buff it.
-
Use newer buffing pads.
-
Apply consistent pressure while buffing.
-
Use a power buffer.
Conclusion
Making your boat look fantastic doesn't have to be intimidating. All you need to do is gather the necessary materials, make sure you have the appropriate tools, and take your time. With over 20 years of marine supply experience, Boat Lover’s Towel has everything you need for drying and cleaning your boat.![The Definitive Guide to Cleaning the Bottom of Your Boat](http://boatloverstowel.com/cdn/shop/articles/Screenshot_2024-05-23_100515-transformed_1_{height}x{width}.png?v=1716440244)
The Definitive Guide to Cleaning the Bottom of Your Boat
Introduction to Boat Maintenance
After a fishing trip or long trek out on the water, your boat's hull may not appear as flawless as it once did due to algae, grime, and water-induced stains covering the previously clear bottom. This may cause you to wonder how to clean the boat's bottom and if the hull will ever return to its original state. While it will take some work on your part, you can clean and restore your boat to its former glory. This blog will help you understand what you need to know to perform boat bottom cleaning.
Importance of Keeping the Bottom of Your Boat Clean
Maintaining a clean boat hull is one of the best ways to get the most out of your boat’s performance, handling, speed, and fuel efficiency. It helps reduce drag and prevents the boat from sitting too low in the water. It also minimizes the transfer of non-native species, which can lead to the loss of local biodiversity.
Antifouling products like ultrasonic antifouling or antifouling paint can help prevent the collection of barnacles, algae, and other sea life on underwater surfaces, but the buildup of them will still occur. Hull cleaning is a critical part of maintaining your boat bottom, even with the use of ultrasonic antifouling solutions.
Tools and Materials Needed for Cleaning
For the best way to clean a boat properly, gather a bucket, brushes, sponges, microfiber towels, a power washer or water hose, and some marine polish. Regular cleaning supplies are not suitable for your boat, as they can leak into the sea, posing a risk to aquatic life. Instead, read product labels and buy marine cleansers designed for safe animal handling.
Steps for Cleaning the Bottom of Your Boat
- Take your boat out of the water. Make sure you have enough room to work, such as a driveway, parking lot, carwash, field, or other spacious area.
- Collect your cleaning supplies. Gather your supplies listed above.
- Wet the bottom of the boat. Wet your boat with a hose or pressure washer, especially if grime is on the bottom. The pressure washer's blast will remove loose debris and dirt from the bottom. If you don't have a water supply, you can use one at a car wash or rent one.
- Use a hull cleaner. Apply a hull cleaner to the boat's bottom, paying attention to trouble spots. Wear gloves and let it sit for two minutes. The cleaner's chemicals disintegrate dirt and stains, allowing for easier removal. Then rinse off the cleaner.
- Dry the boat. After thoroughly washing and rinsing to your desired look, dry the exterior of the boat with a microfiber towel.
- Apply polish. Polishing your boat’s exterior will produce a smooth surface that most filth and grime cannot cling to while also shielding it from weathering and sun damage.
Final Thoughts
Cleaning the bottom of your boat is an important part of extending its lifespan while making sure it’s performing at its best. With over 20 years of marine supply experience, Boat Lover’s Towel has everything you need for drying and cleaning your boat.
Explore Our Shop
![6 Common Mistakes to Avoid When Maintaining Your Boat Hull](http://boatloverstowel.com/cdn/shop/articles/nice-view-ocean-from-boat_23-2148727070_{height}x{width}.jpg?v=1713858603)
6 Common Mistakes to Avoid When Maintaining Your Boat Hull
Hull maintenance is crucial to boat longevity, performance, and safety on the water. The hull is the foundation of the vessel, protecting it from leaks, corrosion, and structural damage. Proper maintenance preserves the aesthetic appeal of your boat and safeguards against costly repairs.
While trying to keep the hull in pristine condition, you may make some common mistakes that inadvertently cause harm rather than offer protection. Understanding these pitfalls is the best way to avoid them. Let’s take a look at the mistakes you should be mindful of when maintaining the hull so you can navigate the waters with greater peace of mind.
The Importance of Maintaining the Boat Hull for Optimal Performance
A well-maintained hull makes for smoother navigation, improved fuel efficiency, and enhanced handling characteristics. By keeping the hull clean and free of damage, you reduce drag, allowing the boat to move more efficiently through the water. Proper maintenance also prevents corrosion and fouling to preserve the integrity of the hull and extend the lifespan of your vessel.
Neglecting Regular Cleaning
Regular cleaning is crucial for maintaining the integrity and performance of your fiberglass boat hull. Neglecting this task can lead to a buildup of grime, algae, and barnacles, which will increase drag and reduce fuel efficiency. Follow these boat hull maintenance tips to avoid these mistakes:
- Clean the fiberglass hull regularly using gentle boat-safe cleaners.
- Use a soft brush or sponge to remove dirt and debris without scratching the surface.
- Rinse the hull thoroughly after each use to prevent salt buildup.
Using Harsh Cleaning Products
Using harsh cleaning products can damage the fiberglass material of your boat hull, compromising its appearance and performance. Prioritize the use of boat-safe cleaners specifically designed for fiberglass boat hull maintenance to ensure effective cleaning without causing harm. Here are some key points to remember:
- Opt for cleaners specifically formulated for fiberglass maintenance on boat hulls.
- Avoid abrasive materials and harsh chemicals that can cause scratches or erosion on the surface.
- Read labels carefully, and follow manufacturer recommendations for safe usage.
Ignoring Damage
Ignoring signs of damage on your fiberglass boat hull can lead to more serious safety and performance issues down the line. Promptly address any signs of damage to maintain the structural integrity of the hull. Consider the following tips:
- Regularly inspect the fiberglass boat hull for cracks, chips, and delamination.
- Address any signs of damage immediately to prevent further deterioration of the fiberglass.
- Seek professional assistance for fiberglass repairs if needed to ensure proper restoration.
Overlooking Proper Storage
Proper storage is key to protecting your fiberglass boat hull from environmental elements and damage during periods of inactivity. Overlooking this aspect can result in premature wear and degradation of the fiberglass. Make sure you:
- Store your fiberglass boat in a dry, covered area when it’s not in use to protect it from UV exposure and moisture.
- Use boat covers or tarps to shield the fiberglass hull from debris and the elements.
- Consider indoor storage options for added protection during long periods of non-use.
Skipping Bottom Paint
Bottom paint serves as a protective barrier against marine growth and corrosion, making it essential for maintaining the integrity of your fiberglass boat hull. Skipping this step can result in increased drag and reduced performance. Remember to:
- Apply bottom paint regularly to prevent fouling and corrosion on the fiberglass hull.
- Choose the appropriate type of bottom paint based on your fiberglass boat's material and usage.
- Follow manufacturer guidelines for proper application and maintenance of bottom paint on fiberglass hulls.
Neglecting Professional Inspections
Regular inspections are crucial for detecting potential issues early on and ensuring the overall health of your fiberglass boat hull. Neglecting this aspect can lead to overlooked problems and costly repairs down the line. Consider the following benefits:
- Professional fiberglass inspections can identify hidden damage or structural issues that may not be apparent during self-checks.
- An expert assessment can help you prioritize maintenance tasks and address concerns proactively to maintain the hull's integrity.
- Regular fiberglass inspections can help extend the lifespan of your boat hull and maintain its resale value.
Premium Boat Hull Maintenance Equipment
At Clean Tools, we take pride in providing top-tier maintenance equipment that keeps your boat in pristine condition for years to come. Our range of boating maintenance tools and accessories is designed to help you feel confident on the water, knowing your vessel is well-cared for. From gentle cleaners to specialized tools, we have everything you need to keep your boat looking its best.
Explore our products today so you can experience the Clean Tools difference.
Explore Our Cleaning Products
![How To Remove Water Spots On A Boat](http://boatloverstowel.com/cdn/shop/articles/beautiful-young-woman-red-cloak-yacht-port-stockholm-sweden_72229-336_{height}x{width}.jpg?v=1711430355)
How To Remove Water Spots On A Boat
Removing water spots on your boat is a chore no skipper enjoys doing. To make this chore easier on you and your boat, follow the steps below from CleanTools to remove water spots from your boat with the best products to do so.
Why Do Water Spots Occur?
No boat owner likes the look of water spots, and more importantly, the damage they can do. Water spots occur due to the hard water in your area. Hard water carries high concentrations of minerals whereas soft water does not. When hard water dries, it leaves behind a mineral called calcium carbonate–aka lime–on your boat. Most freshwater is hard water, and seawater is considered to be very hard due to its dissolved salts. These calcium deposits from hard water can damage your boat's paint, gel coat, varnish, and especially, clear vinyl panels.
Get the Right Cleaning Products
Before you start removing water spots from your boat, make sure you are equipped with the best, most effective cleaning products. You will need:
- Pure Water, Reverse-Osmosis Water, or Soft Water
- Vinegar or A Water Spot Soap Solution
- A Boat Drying Towel
- Waxing Clothes
3-Step Instructions To Remove Water Spots
1. Preparing the Boat for Spot Removal
You first need to prepare your boat by giving it a good rinse with pure water. Then, use a gentle soap of your choice and a non-abrasive sponge to wash the surface of your boat. Clean one small area at a time. Use water and soap first, but if that doesn’t work, then use white vinegar mixed 50/50 with water. The acidic vinegar breaks down the alkaline calcium carbonate so you can wash it away.
2. Rinse, and Rinse Some More
Once your boat is clean, rinse it down thoroughly with pure water again. Rinsing is one of the most important steps in removing water spots from your boat. It may sound counterproductive, but rinsing with pure water ensures that when it dries, it won’t leave behind visible minerals.
3. Dry and Wax for a Sparkling Shine
After you rinse, dry with a super absorbent boat towel. Drying the boat as soon as it gets wet is the most productive thing you can do to prevent water sports from occurring. Once the boat is squeaky clean, you most likely have removed the existing wax and will need to re-wax. The most convenient way to wax and shine your boat is with a waxing cloth, such as The Glosser from CleanTools, which is safe for all finishes.
Tips To Prevent Future Water Spots
Tip One |
Tip Two |
Tip Three |
Chamois, Chamois, Chamois! Take the time to chamois your boat as soon as it gets wet with a scratch-free towel to prevent water spots from forming. |
Don’t Forget the Hull Side Many boats have large hull side windows that must be wiped dry and waxed but are often forgotten. |
Can’t Reach a Spot? If there’s a water spot on your boat but your arms aren’t long enough, try the Boat Lover’s 4-8 Ft. Extension Pole. This pole can attach to a Boat Lovers Towel to dry and remove water spots you can’t reach. |
Give Your Boat a Beautiful Shine With CleanTools
After you take your boat out on the water or during routine cleanings, the last thing you want to worry about is removing pesky water spots. Now you are prepped with the proper steps in removing water spots from your boat to avoid unsightly damage. When you need to maintain your boat, get all the tools you need from CleanTools – the home of the Boat Lover’s Towel. Check out our products and leave us a review! The Absorber® stored on deck. It’s a must-have tool for every boat owner. Not only does The Absorber® thoroughly dry every surface of your boat with care, but it’s also machine washable! Just toss it in the wash after using it. The Absorber® makes daunting boat maintenance a breeze.
See Our Boat Drying Products
![6 Boat Trailer Maintenance Tips](http://boatloverstowel.com/cdn/shop/articles/young-couple-yachting-port_72229-337_1_{height}x{width}.jpg?v=1709183233)
6 Boat Trailer Maintenance Tips
You should be able to enjoy your boat and take advantage of a beautiful day. Keeping your boat trailer maintained makes you the best prepared for all your boat activities.
Here are some tips and tricks on how to best maintain your boat trailer.
How To Maintain Your Boat Trailer
Checking Trailer Tires & Wheels
Problems relating to boat trailer tires and wheels can leave you stranded and even be a safety hazard which is why it’s crucial to check them frequently. When you go to check your tires and wheels, you need to check the tire pressure, tire wear, and any failed wheel bearings. Also, don’t forget a spare tire; it’s great insurance and some trailers don’t come with one.
Testing Trailer Brakes
Just like your car, it’s important to maintain the brakes in your boat trailer. You must first keep them clean, rinsing them after a boating trip to wash off any residue from salt or dirt. You should also have the brake pads or shoes inspected every few seasons to ensure safe performance.
Replacing Trailer Lights if Needed
You should check all the lights in your boat trailer before every use and replace any if needed. Most new trailers have LED lights that are good for years, but the incandescent light bulbs in older trailer lights will burn out quickly. Maintaining your boat trailer lights will keep them working and prevent corrosion.
The Best Boat Trailer Maintenance Tips
Following these tips can help you feel confident about taking your boat back out on the water.
#1 Tip: Rinse and dry your boat trailer after using it.
The first tip we have to keep your boat maintained is simple: Always give it a good rinse after using it. Rinsing your boat trailer is important in preventing corrosion from saltwater, dirt, and grime. After you rinse, use our boat drying products to effectively dry and shine your boat trailer without leaving any residue or fibers behind.
#2 Tip: Grease trailer wheel bearings every couple of months.
Along with checking your wheel bearings, you have to grease them every couple of months. We also recommend using wheel-bearing protectors.
#3 Tip: Check tire pressure at least once a month.
Put a reminder on your phone or a sticky note on the fridge to check your boat trailer tire pressure at least once a month. Make sure they are at the correct PSI, which should be indicated on the tire sidewall. Along with checking your tire pressure, we recommend carrying an inexpensive air pump with an extension cord to fill your tires if you need it.
#4 Tip: Check your brake fluid and brake pads.
Check the boat trailer's brake fluid in the master cylinder a couple of times a season. The fluid level will go down as the brake pads wear. If the brake fluid levels get too low, you could start a leak in the brake system, which can put your boat trailer out of commission.
#5 Tip: Clean your boat trailer light connections.
Trailer light connections are often missed in cleanings. To keep the light connections from corroding, wipe them clean with a towel and spray them with a corrosion blocker. The best type of towel to use is the boat lover’s towel for its super absorbency and shine qualities.
#6 Tip: Check your wheel lug nuts for tightness.
To polish off your boat trailer maintenance routine, check your wheel lug nuts for tightness. It’s best practice to take them off all the way, put a little grease on them, and screw them back. Every six years you should replace the tires on your boat trailer, according to the National Transportation Safety Board.
Maintain Your Boat Trailer With CleanTools
Boat trailer maintenance allows you to get back out on the water to do what you love with peace of mind that you’re properly prepared. Feel prepared to do what you love with the best boat trailer maintenance tools. Home of the boat lover's towel - get yours today at CleanTools.![What Type of Paint Should You Use on a Jet Ski?](http://boatloverstowel.com/cdn/shop/articles/Screenshot_2024-02-05_174446_1_1_{height}x{width}.png?v=1707285184)
What Type of Paint Should You Use on a Jet Ski?
The paint you choose for your jet ski depends on your budget, what the hull of your jet ski is made of, the area of the jet ski you’re painting, and the look you want.
There are several types of paint you can use for different areas of your jet ski. There’s more durable paint for your jet ski’s hull, which spends the most time underwater, and there’s topside paint, which is used for the areas that do not become fully immersed in water.
Here are some common types of jet ski paint and how to apply it.
Choosing the Right Paint for Your Jet Ski
Basecoat-Clearcoat Paints (BCCC)
BCCC paints are a budget-friendly option. They require only one coat of paint, unlike other types of jet ski paint. Basecoat paints are less prone to oxidation, and they help improve your fuel efficiency.
However, BCCC paints are sensitive to abrasions and scratches, so you have to be careful when cleaning your jet ski. Don’t use any abrasive polishing or rubbing compounds. If you take care of your basecoat paint, it can last for a long time.
Epoxy Paints
Epoxy paints are a mixture of hardener and epoxy resin, and they provide a solvent-resistant, durable finish. The amount of epoxy paint you need per square foot is lower relative to other types of jet ski paint.
Because epoxy paints resist abrasions, they have a long lifespan, as long as you clean your jet ski after each use and remove all residual moisture.
If you want to change your jet ski paint frequently, epoxy paints aren’t a good choice since they can be difficult and costly to remove.
Enamel Paints
Enamel paints are known to be able to withstand different weather conditions, and they provide a stunning, glossy finish. They’re also easy to use—they dry very quickly, and they last a long time once hardened.
However, enamel paints are a more costly option.
Polyurethane Paints
Polyurethane-based paints are popular for cars, boats, and jet skis. They can resist extreme weather and provide a high gloss, consistent finish.
They are also self-cleaning, meaning dirt and dust can be washed away automatically. However, polyurethane paints are not the most durable option. They can also alter the color of wood surfaces.
How To Paint a Jet Ski
Pre-Procession
Locate a covered space where you can paint your jet ski without anything damaging your paint coat. However, make sure this space is well-ventilated—jet ski paints are not safe to inhale.
You’ll also need a mount where you can place your jet ski so it remains stable during painting.
Preparations
Start by washing your jet ski and removing all stickers from the body.
Next, sand off the old paint to create a good foundation for the new paint.
Take off all the parts of the jet ski you can, and then mask and tape all the parts you can’t.
Painting
Once you’ve sanded the jet ski and applied primer, it’s time to paint. Mix the paint according to the instructions. Don’t mix too much at once or it will dry out before you’ve applied it.
Next, fill up the paint spray gun container. Spray a bit on a piece of cardboard to make sure everything’s working properly.
As you paint the hull, work in thin coats to stop the paint from running. You’ll probably need to apply four coats.
Allow the paint to get tacky between coats.
FAQs
Can I Use Spray Paint on My Jet Ski?
Spray paint cans are not a good option for jet skis. Since the hull of your jet ski will spend most of its time underwater, you need a more durable option, like hard bottom paints or hybrid or semi-hard paints.
If you’re going to use a can of paint, you’ll need a paint sprayer, though.
What’s the Best Paint for Jet Skis?
You can paint the top deck of your jet ski with any waterproof gelcoat paint since it doesn’t get fully immersed in the water.
When it comes to jet ski hull paint, you need a more durable option. For the part of the hull that’s above the water line, you can use polyurethane or enamel topside paint. For the part that’s often underwater, you can use acrylic marine paint or epoxy marine paint.
Should I Have My Jet Ski Professionally Painted?
If you want a custom-painted jet ski, taking it to a shop is a good idea. Professionals have stencils and patterns to follow, as well as more experience applying the correct thickness of paint.
Additionally, if you’ve never worked with sandpaper or a paint spray before, you might want to get your jet ski professionally painted.
Keep Your Jet Ski Looking Sharp With CleanTools
A high gloss finish on your jet ski always starts with a good wash. Whether you’re taking care of your epoxy paint coat or getting ready to apply a new coat of paint, you’ll need a marine boat cleaner and a few highly absorbent towels. With a few wipes, the Boat Lover’s Towel will have your jet ski sparkling, free of debris, and ready to hit the water in style.
![What Is Bottom Paint For Boats and Does My Boat Need It?](http://boatloverstowel.com/cdn/shop/articles/Screenshot_2024-01-10_124257_720x1115_1_{height}x{width}.webp?v=1705041019)
What Is Bottom Paint For Boats and Does My Boat Need It?
Bottom paint on boats is designed to repel aquatic organisms, plants, and algae that can damage the hull, affect the boat’s performance, and create a continuous maintenance chore. Bottom paint is ideal for boats that stay in the water for long periods of time.
Read on to learn more about what bottom paint does, how to choose the right paint for your boat, and how to maintain your boat.
What is Antifouling Paint For Boats?
Bottom paint or antifouling paint are interchangeable terms for paint that is applied to the bottom or hull of a boat. This paint acts as a protective layer for the part of the boat that sits in the water.
Bottom paint can also be applied to the lower unit of the motor and trim units.
Most boats don’t come with bottom paint; it’s something you add aftermarket. If your boat is going to be sitting in the water for long periods of time, it may be a good idea to apply bottom paint.
What is the Purpose of Bottom Paint?
The formula of bottom paint wards off marine growth, keeping the hull cleaner and leading to less discoloration.
A layer of bottom paint also makes it easier to clean the hull of your boat, as marine growth will come off easier than it would if your boat were not painted.
Cleaning is important because a buildup of marine growth on the hull can hinder your boat’s speed and cause lower fuel efficiency and performance from your engine.
How to Choose the Right Bottom Paint For My Boat
Bottom paint is mainly recommended for those who boat in saltwater and particularly for those who plan to leave their boat sitting in the water.
Coastal areas usually see the most sunlight throughout the year, and the more sun there is, the more growth happens on the seafloor. Hulls in these areas are more susceptible to the buildup of marine growth, and the antifouling properties of bottom paint prevent the rapid growth of buildup.
Excessive marine growth on the hull can break through the gel coat of a fiberglass boat and leach into the fabric of the boat. This can cause blistering that allows water into the fiberglass and leads to delamination. If the salt water breaks through because of delamination, it will eat away at the material of the hull.
Saltwater also speeds up oxidation, which leads to discoloration of the hull.
There are different antifouling formulas depending on the material of the hull. For example, pontoons need a different type of bottom paint than wooden or fiberglass boats do.
What Are the Steps to Bottom Painting?
First, you need to determine the waterline and create a straight tapeline that makes a clean border between the bottom and the side of your boat. Previous marine growth can direct you where to make this line.
If your boat bottom has never been painted, the next step is to use 60 or 80-grit sandpaper to scuff sand the gel coat to remove any wax or debris and create a smooth surface that the paint can adhere to. You should also fill in any chips in the gel coat and sand smooth.
If your boat bottom was previously painted, light sanding is required to remove any debris and create a good adhesive surface.
Generally, one to two coats of antifouling paint provide adequate protection.
After painting, pull the tape off while the paint is fresh, and launch your boat after the paint dries overnight or soon after.
How Often Does Bottom Paint Need To Be Applied?
On average, a properly applied layer of bottom paint should last two to three years if you use your boat regularly. If your boat sits at the dock in the water year-round and you take it out for cleaning only once or twice a year, the paint will not last as long. In this case, you should re-apply the paint every year.
FAQs
What Is Marine Paint?
Marine paint is a urethane paint that is specifically formulated for boats and leaves a glossy finish. It’s one option you can choose for your boat’s hull. Another option is gel coat, which is a resin-based finishing material that dries into a hard, shell-like casing.
What Is the Best Bottom Paint For Boats?
The bottom paint you should choose depends on what kind of boat you have and your boating habits. If your boat sits in the water and stays there, you need “hard” bottom paint. If you use your boat frequently and pull your boat out of the water sometimes, ablative bottom paint is a good choice.
What Is Ablative Bottom Paint?
Ablative bottom paint is self-polishing paint that wears off the surface paint as your boat moves through the water. As the paint sloughs off, it exposes fresh paint that continuously protects your boat’s hull. When you put your boat back in the water, it softens the paint, and the protection is activated.
If you don’t use your boat frequently, ablative paint is not a good option for you, because it requires your boat to be in motion to expose the fresh paint surface. On the other hand, if you have a high-performance boat and often run at high speeds, ablative paint is too soft and will wear off quickly.
Glide Through the Waves With CleanTools
Whether you have bottom paint on your boat or not, cleaning is an essential part of boat maintenance. Regular cleaning, including waxing, makes it harder for marine critters to stick to the hull and keeps your boat looking sleek and sparkly for longer. For effortless cleaning, choose the Boat Lover’s Towel and get back on the open water in no time.![How to Remove Barnacles From Your Boat](http://boatloverstowel.com/cdn/shop/articles/How_to_Remove_Barnacles_From_Your_Boat_{height}x{width}.jpg?v=1699600171)
How to Remove Barnacles From Your Boat?
Barnacles on boats are not only unsightly, but they also cause resistance that decreases speed and increases fuel consumption. They can be stubborn critters, but there are some tried-and-true ways to remove them.
Read on for the best ways to remove barnacles from your boat’s bottom.
Manual Barnacle Removal
If barnacle buildup is extensive and covers large areas of your boat’s hull, you can use a pressure washer to remove the bulk of it. Be sure to spray the pressure washer parallel to the hull’s surface to avoid making gouges in the fiberglass.
Pressure washing is not very effective on young barnacles and runs a higher risk of damaging the gel coat.
For small patches of barnacles or those left after pressure washing, remove them with a scraper. It’s best to start with a wooden or plastic scraper to reduce the risk of damage. You may have to use a metal paint scraper for stubborn barnacles. Scrape parallel to the hull’s surface to get underneath the shells of the barnacles.
After the barnacles are removed, they may leave behind a calcium-based residue known as a husk, which needs to be chemically removed.
Chemical Barnacle Remover
Mild boat hull cleaners contain either a calcium remover (lime remover) or a weaker acid like oxalic, phosphoric, or citric acid to help remove barnacle residue. Apply a boat cleaner with a nylon brush and let it sit so the chemicals can take effect. Then wash and gently scrape off the residue. You may need to repeat this process several times to remove all husks.
If mild boat cleaners and acids are not effective after several attempts, you will need to use muriatic acid, which is a type of hydrochloric acid (HCl). Muriatic acid is highly corrosive and can damage your eyes, skin, and lungs, as well as paint, gel coat, metal, and plastics.
Handling muriatic acid requires gloves, protective clothing, and a respirator mask. It is recommended that only professionals use this acid as a hull cleaner.
How to Remove Barnacles From Boat in Water
If you need to remove barnacles while your boat is docked, manual removal is the best method. Use the gentlest scraper you can to remove the bulk of the barnacles. Use a metal paint scraper or putty knife only if necessary.
Pressure washing is a better choice for when your boat is on land and the barnacles have had time to dry out.
How to Get Barnacles Off Your Boat’s Motor
To get barnacles off your boat’s outboard motor, use a calcium remover or mildly acidic boat hull cleaner and a stiff-bristled brush. Let the cleaner sit before scrubbing. You’ll likely have to repeat this process a few times. Be sure to only use a mild cleaner to avoid damage to the paint, plastic, metal, or gel coat.
How to Remove Barnacles From Boat Lift
You should rinse your boat lift with fresh water after each use to avoid barnacle growth in the first place. But if there are already barnacles on your boat lift, follow the same steps to remove them as you did for the rest of your boat. If your boat lift is made of aluminum, be sure to use an aluminum-safe cleaner.
Keep Barnacles at Bay With CleanTools
The more often you remove barnacles from your boat’s hull, the easier it will be to maintain and keep barnacles off. This also means there will be less risk of damage to your boat’s paint. All you have to do is incorporate barnacle removal into your boat’s regular maintenance. So scrape them away, and then pick up the Boat Lover’s Towel to clean, polish, and wax your boat for a slick, shiny surface that will make future barnacle removal even easier.![How to Clean The Bottom of a Boat ?](http://boatloverstowel.com/cdn/shop/articles/how_to_clean_bottom_of_boat_{height}x{width}.jpg?v=1697173946)
How to Clean The Bottom of a Boat ?
Table of Contents:
To keep your boat looking its best, you should wash the bottom of your boat about once a month or as soon as you notice stains, algae, or dirt on the hull. This will protect your boat from damage, increase its overall lifespan, and make things easier once it comes time for cleaning.
Here’s how to clean the bottom of your boat.
1. Take Your Boat Out of the Water
It’s possible to clean your boat while it’s in the water, but this process is more labor-intensive and requires more supplies. You’d need scuba gear, water-safe cleaning supplies, and a good amount of time.
To make the cleaning process easier, take your boat out of the water and bring it to a car wash, field, driveway, or parking lot.
2. Gather Your Cleaning Supplies
Once your boat is on land and ready for cleaning, it’s time to gather your cleaning supplies.
Here are the boat bottom cleaning tools that you’ll need:
- Hull cleaner
- Water hose / power washer
- Bucket
- Brushes
- Sponges
- Soft, absorbent towels
- Marine polish
- Gloves
Before you begin, note that you cannot use everyday cleaning products to clean your boat. These products are not safe for marine life and can be harmful if they enter the water. Use marine cleaners that are specifically designed to be safe for marine wildlife.
3. Wet the Boat Bottom
To start the cleaning process, wet the boat with a hose or pressure washer. If the grime on the boat bottom is thick, start with the pressure washer and use the hose later. A pressure washer will remove the outer layer of dirt and any loose materials clinging to the bottom.
If you don’t have a water source of your own, you can rent one or take your boat to a car wash.
4. Apply a Hull Cleaner
Once the bottom of the boat is wet, begin to apply a hull cleaner. Be sure to wear gloves, and focus on problem areas first. You can use brushes, sponges, or rags to work in the hull cleaner. Then, let it sit for at least two minutes.
During this time, the ingredients in the hull cleaner will start breaking down the grime and stains on the bottom of your boat, loosening them for the next round of rinsing.
After you’ve let the cleaner sit for at least two minutes, take your hose and rinse the bottom of the boat until the cleaner is gone.
One application of hull cleaner may be enough to clean the bottom of your boat, but if not, repeat this process until you achieve your desired results.
5. Dry the Boat
Once you’ve thoroughly rinsed all the hull cleaner from your boat, take a clean towel and dry the exterior of your boat. Completely drying it will prevent water spots from forming on the hull and allow you to take a closer look and check for missed dirt.
Also, the sooner your boat is dry, the sooner you can move on to the final step in the cleaning process.
One thing to note is that you should avoid using rough towels that can scratch your boat’s exterior and paint job. You should use soft towels or towels specifically designed for boats .
6. Apply Boat Polish
Polishing your boat after cleaning it is a step you don’t want to skip. Marine polish creates a slick surface that most dirt and grime cannot stick to, which will keep your boat cleaner for longer. Polish also protects the exterior of your boat from sun damage and weathering.
You should follow the directions on the boat polish that you choose, but you’ll always start by applying the polish to the exterior of your boat in small circles with a soft towel and waiting for it to dry.
How to Clean the Bottom of Your Fiberglass Boat
You can clean fiberglass boat bottoms by following the above steps. The most important thing to do is to clean the hull of your boat regularly to avoid fouling, or the buildup of marine organisms. The “glue” left behind by these organisms can damage both fiberglass and wooden hulls.
How to Clean the Bottom of Your Boat in the Water
If you decide to clean your boat while it’s at the marina, there are a few things to keep in mind. First, check the restrictions in your local marina to confirm that you’re allowed to clean your boat there.
Next, determine the type of antifouling paint that is on your boat hull. Soft or ablative antifouling paint should be cleaned by gently sweeping a soft cloth along the surface of the hull. Scrubbing ablative paints will cause toxic chemicals to be released into the water, which can harm marine wildlife and enter water and food sources.
Hard bottom paint can be scrubbed a bit more thoroughly than ablative paint, but you should still use the least abrasive material that is effective for the job. For example, using a wire brush will still cause some bottom paint damage and release toxic chemicals into the water.
Underwater boat hull cleaning tools must include something to scrape off marine growth since you can’t use a hose or power washer underwater. Examples include wood planks, scrubbing pads, and firm-bristled brushes. You’ll also need work gloves and snorkeling or scuba gear.
Maintain Your Boat’s Bottom With CleanTools
No matter the material of your boat and whether you’re cleaning the hull on land or in the water, you need a quality soft towel for cleaning, polishing, and drying. The Boat Lover’s Towel will simplify your boat’s maintenance routine and get it back to gliding through the water in no time.
Explore Our Shop
![boat vinyl window cleaner](http://boatloverstowel.com/cdn/shop/articles/boat_window_cleaning_{height}x{width}.jpg?v=1695020639)
How to Clean Plastic Windows on a Boat ?
Table of Contents:
- How to Clean Boat Windows Without Scratches?
- Step-1: Use the Right Cleaning Solution
- Step-2: Pre-Clean the Windows
- Step-3: Clean the Windows With the Proper Tools
- Step-4: Remove Any Remaining Water Marks or Streaks
- FAQs
- 1) How often should I clean plastic boat windows?
- 2) How do I remove scratches from plastic boat windows?
- 3) How do I clean glass boat windows?
- Make Your Boat Windows Sparkle With CleanTools
When you’re out on the river in your boat, you want to be able to look through crystal-clear windows and see the sparkling water and beautiful natural scenery. But if you have plastic windows, they’ll eventually become cloudy and lose their luster, obscuring your view of the boundless waters and landscape.
Most boat windows are made of one of two types of plastic: acrylic and vinyl. Acrylic windows need to be cleaned with gentle products to avoid wearing them down. Vinyl windows tend to become cloudy as they’re exposed to the sun, which causes the plasticizers on their surface to evaporate. Regular cleaning helps to reduce the damage associated with this evaporation.
Plastic doesn’t behave like glass, and it can be easily scratched and damaged if you use the wrong products or cleaning technique. When it’s time to clean your windows, follow these steps on how to clean vinyl or acrylic windows on a boat.
How to Clean Boat Windows Without Scratches?
Boat window cleaning is a relatively simple process that requires only a few supplies. You’ll need two buckets (one for soapy water and one with clean water for rinsing), soft, absorbent cloths, and a boat vinyl window cleaner.
Step-1: Use the Right Cleaning Solution
Harsh cleaners like ammonia, alcohol, and bleach should never be used to clean plastic boat windows. They react with the plastic and cause it to break down, resulting in irreversible damage.
You can use a mild, non-detergent soap, which is a soap that does not contain any synthetic compounds that will react with the plastic. To err on the side of caution, opt for a specially formulated boat vinyl window cleaner. Marine cleaners for plastic windows work for both vinyl and acrylic windows, and they also contain UV protectants to prevent yellowing from UV damage.
Step-2: Pre-Clean the Windows
To start the cleaning process, rinse your windows down to get rid of dirt and debris. If you skip this and start wiping your window while there’s still dirt on it, you could end up seriously scratching the plastic. So rinse your windows a few times to soften or remove as much dirt as you can to reduce the amount of scrubbing needed later.
Step-3: Clean the Windows With the Proper Tools
When you’re done rinsing the windows, grab a soft cloth and fill a bucket with your boat window cleaning solution. Dip the cloth into the solution, wring it out, and wipe the first window in left-to-right motions. Don’t re-wipe an area you’ve already cleaned to avoid tracking dirt back across the window and scratching it.
Rinse out your cloth and repeat until the window is clean. Then, get a new, clean cloth, dip it into a bucket of clean, warm water, and wipe the window to remove any remaining soap residue.
Repeat this process for all of your boat windows. For top-notch boat windshield cleaning, replace your used cleaning solution with fresh water and boat window cleaner often so you don’t track dirt from window to window.
Step-4: Remove Any Remaining Water Marks or Streaks
If there are water marks or streaks on your windows after cleaning them, you can remove them with a mixture of 90% water and 10% vinegar.
Use a clean cloth to apply this mixture and gently wipe away the water marks.
FAQs
1) How often should I clean plastic boat windows?
To reduce the amount of rinsing and wiping you have to do next time you clean your windows, clean them with mild soap and a soft cloth once a week.
To protect your windows from wear, apply a special boat window cleaner, like the ones mentioned above, every four to six weeks. Boat window cleaners with protectants keep your windows clean longer while also safeguarding them from UV damage.
2) How do I remove scratches from plastic boat windows?
If you haven’t cleaned your boat windows in a long time and you notice yellow markings and many tiny scratches, the windows need to be polished. You’ll need an electric polisher, polishing pads, a very fine polishing compound, and a soft cloth.
First, you should remove the windows and lay them on a flat surface. Then, use a clean cloth to apply the polishing compound to the window. Because plastic windows scratch easily, you’ll need to use a very fine-grit polishing compound.
Use your polisher to apply light pressure at a low speed. If your polisher is set too high, you risk melting the plastic.
Make sure to always keep the pad moving. Once you’re done, just pop your windows back in and they should look much better.
3) How do I clean glass boat windows?
Since glass behaves very differently than plastic, you’ll want to use a boat glass cleaner to clean glass surfaces on your boat. But similar to the plastic boat window cleaning process, you should use two cloths to clean glass. Spray the glass cleaner and wipe away dirt and grime with the first cloth. Then buff away streaks with the second cloth.
Make Your Boat Windows Sparkle With CleanTools
Whether your boat has acrylic, vinyl, or glass windows, a specialized cleaning solution and a soft cloth are really all you need to bring the luster back to your boat windows. Once you’ve rinsed off as much dirt as possible, a soft cloth will help you apply the cleaner, remove grime, and protect your windows, all without scratching them. When you choose The Boat Lover’s Towel , you’ll be back on the water enjoying those beautiful views before you know it.
Shop Boat Cleaning Products
![how to clean non-skid boat deck](http://boatloverstowel.com/cdn/shop/articles/boat_deck_cleaning_{height}x{width}.jpg?v=1692249563)
5 Steps to Clean a Non-Skid Boat Deck
Table of Contents:
- How to Clean Non-Skid Boat Deck:
- Vacuum the Deck
- Prepare a Cleaning Solution & Wet the Deck
- Scrub the Deck
- Rinse the Deck
- Dry the Deck
- FAQs
- What is Non-Skid Deck Wax?
- How Do I Wax a Non-Skid Boat Deck?
- How Do I Remove Oxidation from a Non-Skid Boat Deck?
- How Do I Clean a Fiberglass Boat Deck?
- How Do I Remove Stains from a Fiberglass Boat Deck?
- Keep Your Non-Skid Boat Deck in Top Condition With CleanTools
Non-skid boat decks are intended to improve your footing and reduce slips, falls, and injuries. Not cleaning non-skid surfaces regularly decreases their effectiveness, and caked-on dirt and grime can wear down the surface prematurely as foot traffic grinds it into your deck, causing abrasions.
Cleaning a non-skid boat deck is fairly straightforward, but there are still some things you should know to avoid creating a mess or being left with a splotchy finish on your deck. Here you can find tips on how to clean your boat’s deck as well as answers to common questions from boat owners about deck maintenance, how to clean boat floors, and what could be the best ways to clean non-skid boat decks.
How to Clean Non-Skid Boat Deck:
If you’re wondering how often you should clean your boat’s deck, it depends on how often you use it. It’s best to clean it after every few outings or when it starts looking dirty.
For the cleaning process, you’ll need a soft-bristled brush, a non-skid boat deck cleaner, two buckets, fresh water, a cloth or towel, and a hose or sprayer.
Vacuum the Deck
To avoid a slurry of wet dirt, first vacuum your boat’s deck to remove loose or bulky dirt and dust buildup before you apply your cleaning solution.
Prepare a Cleaning Solution & Wet the Deck
Mix a non-skid deck cleaner with warm water in a large bucket according to the instructions on the cleaner. Then wet your boat’s deck with fresh water to loosen the dirt and grime trapped in its non-skid surface.
Scrub the Deck
Use a soft-bristled brush and the cleaning solution to remove dirt and stains from your boat’s deck without scratching it.
Rinse the Deck
Fill a new bucket with fresh, clean water to rinse off the dirt residue and remaining cleaning solution. You can also use a sprayer to push the cleaner and dirt out of the deck. Make sure to rinse the entire deck thoroughly so you don’t leave behind dirt or streaks of cleaning solution.
Dry the Deck
Completely dry your boat’s deck with an absorbent towel to prevent moisture-related issues like mold and mildew and to ensure a clean finish.
FAQs
What is Non-Skid Deck Wax?
Non-skid deck wax is designed for use on the textured surface of a non-skid boat deck. It contains stain-resistant ingredients and UV inhibitors to protect your deck from corrosion, oxidation, water spots, and sun damage without making it slippery.
Waxing your boat’s deck creates a barrier between it and dirt, debris, fish products, and everything else it comes into contact with. When it’s time to clean the deck, these materials will be much easier to clean off of a waxed surface because they have not become ground into the texture of the non-skid deck.
How Do I Wax a Non-Skid Boat Deck?
You should wax your boat’s deck yearly to protect it and maintain its finish. For the waxing process, you’ll need non-skid boat wax, a buffing machine, and a soft cloth.
- Apply the Wax : After washing and drying your boat deck, apply the non-skid wax directly in circular sections. Be careful not to use too much wax, as it will get messy.
- Buff the Wax : Use a buff pad or a buffing machine to rub the wax into the desk in circular motions. Buffing tools spread the wax evenly without streaks and create a glossy sheen that makes your deck look new. Place the buffer head on the surface of your deck before turning it on so it doesn’t sling the wax everywhere. Move your buffing tool in a side-to-side, overlapping pattern. Repeat this motion slowly until the wax has almost disappeared.
- Wipe Away Excess Wax : Remove excess wax with a soft cloth to avoid developing stains from too much wax in one area. This will also keep the deck from looking blotchy.
How Do I Remove Oxidation from a Non-Skid Boat Deck?
Cleaning and waxing won’t get rid of dull areas from oxidation on your boat. For heavy oxidation, you'll need to use an electric polisher like a Makita and follow it up with a boat polishing compound. For lighter oxidation, you can use a boat polishing compound. Use medium-cut compounds for fading and staining and light-cut compounds for cleaning.
How Do I Clean a Fiberglass Boat Deck?
Fiberglass boat decks can be cleaned with a non-skid boat cleaner according to the above steps. Non-skid boat cleaners can also be used to clean smooth, non-textured surfaces on your boat, including fiberglass, metal, plastic, vinyl, and rubber.
How Do I Remove Stains from a Fiberglass Boat Deck?
For stubborn stains on a fiberglass boat, apply a medium-cut boat polishing compound—formulated for fiberglass surfaces—with an electric polisher.